Search Results

Max, Im deiner Aufzählung fehlt die Ausbeutung der Arbeiter, du unter prequersten Verhältnissen die Klampfen zusammenbauen. Ist was anderes als aus USA oder europäischer Fertigung. Ich würde sowas nicht kaufen. Aber es soll ja auch Leute geben, die zu Primark, Kik osw. Klamotten kaufen... Es gibt nichts gutes im Schlechten... Dann lieber mittleres Preissegment aus Japan oder Mexiko. ...Meine Meinung

Looks like there is a short circuit between your DC-Jack Wiring and on the pot next to it. Please shorten the unisolated tips of your wiring to avoid short circuits when they are touching each other, the enclosure, the pots and soldering points. If you have no bypassed signal there is something wrong with you in- and output wiring and you maybe your footswitch. Doublecheck that please. And please shorten and organize your hole offboard wiring so that we are able to comprehend it.

Buy a simple multimeter for 20-30 EUR. It’s an essential tool for a long time. Then you are able to check the voltage. So doublecheck every soldering point. Doublecheck the hole wiring. Do you hear the bypassed signal when the effect is off? Does the LED light up if you turn on the pedal?

Find das Teil garnicht so schlecht. Wenn man da ein bißchen Arbeit und Geld für ordentliche Teile reinsteckt, ist das vielleicht ne ganz orderntlich Klampfe. Los Micha, hol dir das Teil Oder verkaufst du das etwa?

I think you are able to translate him relevant informations into English if necessary

Vielleicht waren da noch andere Dämpfe im Spiel?!

Simon, hast du beim Löten dein Deutsch verlernt?

Perfect. So enjoy your Muff And if you do a nice enclosure design it would be cool to see some photos of it.

Tolles Projekt. Wenn das ein neuer Bausatz wird, bin ich äußerst interessiert

Your soldering points don't look that good. First resolder the small 3pdt pcb - the soldering of the switch and for in- and output don't look like they are properly soldered. Second double check all soldering poins on your main pcb - this pcb is a double sided one. That means you have to solder every soldering point on both sides. Finally check the propper fitting of the transistor in their sockets and shorten the three legs to that the transistor don't touch the housing.

Welcome to forum. No, a pop while turning the pedal on or off is not normal. Please checkout your wiring especially the ground wiring. The help you and to see what may be the reason for this issue please add some photos of your pedal (pcb, wiring etc.) and add the related link for this kit / pedal.

Sehr schick geworden

First of all - welcome to musikding community. This pedals is not really for beginners. To check if it’s working first turn the comp and stab pot. All pots (especially stab and comp) are very interactive. Btw: Your pot wiring is not that good. Especially the wiring between soldering point 2 of the pcb and the drive pot seams to be burned. Please double all of your Offboard wirings. But maybe it’s still working but you don’t have the right parameters Try out some of these:

2. No, unfortunately not. Check out the resistor value of the pot (lug 1 and 3). Is there a change and does the pot have the value as indicated? 3. Try another of the same ICs. How are the voltage values on the 8 legs of the IC when it is in its socket? 4. Yes please.

Hab das mit dem Fox(x) etwas zu wörtlich genommen

Checkout the voltage on the IC - maybe it’s broken. Or you have to readjust the trimpot.

Guck mal inner Bucht und filter nach deutschen Anbietern. Dann bekommst du die MMBF4393s für’n paar Euro. alltransistors.com/mosfet/crse…d=0.03&rds=100&caps=SOT23

And please check if the IC is still fixed in its socket.

Wo wir grade bei Russen-Tretern sind Am letzten Wochenende fertiggestellter Russian Green Muff Und mein Peter und der Wolf Double Fuzz